Brownells Hole Center Punches #6 Hole Center Punch US Specifications
Gunsmith Punches by Brownells
|
Technical data & information: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-732-006.
 Indicative Price: USD 8.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting items : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Grace Usa Brass Punch Set 5/16" (7.9mm) Brass Pin Punch US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For drifting sights, driving pins or fitting parts when marking or scratching the surface can mean the difference between a job well done and disaster. Machined from premium, brass hex. Punch set includes 8 flathead, long shaft punches for driving pins completely out. Mfg: grace usa specs: brass, 5⁄16" (7.9mm) hex stock. Punch set, 8 punches: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16", 7⁄32", ", 5⁄16" dia. US specification & reliable quality gunsmith punches by Grace. Part Nr: 516BPP.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #4 Roll Pin Punch US Specifications
USD 6.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25003939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Starter Punch Set US Specifications
USD 22.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-513-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #6 Punch US Specifications
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25035939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch 1/4" Aluminum Punch Tip US Specifications
USD 4.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-475-005.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .151" Diameter Steel US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-031.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .246" Diameter Brass US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-027.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pins 2 1/2"x.091" US Specifications
USD 15.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Finally! what we think is the answer to the pin punch headache that has plagued us, and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now, just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel, tensile strength of over 140,000 psi (min.). Replaceable punch, the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2β½" (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 β½" lengths. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-510-691.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch 5/16" Aluminum Punch Tip US Specifications
USD 4.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-475-006.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Hole Center Punches #6 Hole Center Punch US Specifications
|
 Copyright © RexGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
