Brownells Roll Pin Starter Punches #2 Punch US Specifications
Gunsmith Punches by Brownells
|
Technical data & information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25031939.
 Indicative Price: USD 7.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting items : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Gauge Rite Products Top Dead Center Punch US Specifications
USD 37.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: The tdc is a rugged, foolproof tool to end the problems of off-center-work, broken taps and drills that come about from trying to "eyeball" top dead center on gun barrels or other round stock. Simple to use, just level and plumb the rifle on the drill press, place tdc on barrel or receiver, level the bubble and tap the punch. The punch mark is top dead center. Precision made; shockproof level. Mfg: gauge-rite products specs: body, 1-15/16" (23.8mm) x 1-β½" (3.8mm) x 1" (2.5cm), aluminum. Punch, βό" (6.3mm) diameter tool steel. Locating rod, 5-β½" (14cm) long. US specification & reliable quality gunsmith punches by Gauge-Rite. Part Nr: 871-100-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Hole Center Punches Set US Specifications
USD 21.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-732-000.
More Details : click here
SEARCH this site : click here
|
|
|
Starrett #565 Pin Punch Set Starrett Pin Punch 1/16" US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Precision ground from specially selected tool steel, hardened and highly polished, the starrett pin punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly. Mfg: starrett specs: 4" (10.2cm) long. Sizes: 1/16" (1.6mm), 3/32" (2.4cm), 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (5.5mm), βό" (6.3mm) and 5/16" (7.9mm). US specification & reliable quality gunsmith punches by Starrett. Part Nr: 52578.
More Details : click here
SEARCH this site : click here
|
|
|
Grace Usa Brass Punch Set 5/32" (4mm) Brass Pin Punch US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For drifting sights, driving pins or fitting parts when marking or scratching the surface can mean the difference between a job well done and disaster. Machined from premium, brass hex. Punch set includes 8 flathead, long shaft punches for driving pins completely out. Mfg: grace usa specs: brass, 5⁄16" (7.9mm) hex stock. Punch set, 8 punches: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16", 7⁄32", ", 5⁄16" dia. US specification & reliable quality gunsmith punches by Grace. Part Nr: 532BPP.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 5/64" Diameter Roll Pin Holder US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. US specification & reliable quality gunsmith punches by Brownells. Part Nr: B564RSH.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches Kit US Specifications
USD 34.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-241.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Deluxe Punch Bench Set Pin Punch Set US Specifications
USD 105.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: This deluxe punch set gives you a versatile selection of 20 punches to easily start, remove and install pins, align holes, plus drift and stake sights without marring the part or firearm finish. We combined alignment punches, flat tip mini punches, starter punches, a nylon drift punch, and a center and prick punch with our most popular pin punches, then added a machined delrin bench block to hold and organize them all for easy access. Punches are constructed of hardened steel with parallel-ground shanks and either knurled or hexagonal handles. The nylon drift punch is solid nylon and can be shaped for your specific application. Alignment punches feature a tapered pin with a working leng mfg: brownells specs: steel, knurled or hexagonal handle, except nylon drift punch is solid nylon. Nylon punch, contains (1), 4" (10cm) long x 5/16" (7.9mm) diameter. Alignment punches, contains (1) of each diameter: .070" (1.8mm) to .156" (4.0mm); .110" (2.8mm) to .187" (4.7m. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-653.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Roll Pin Starter Punches #2 Punch US Specifications
|
 Copyright © RexGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
