Mayhew Steel Single Starting Punches 1/16" Starting Punch US Specifications
Gunsmith Punches by Mayhew
|
 Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Roll Pin Starter Punches #6 Punch US Specifications
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25035939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Hole Center Punches Set US Specifications
USD 21.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-732-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Pins (6) 1"x.039" US Specifications
USD 9.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-513-639.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .151" Diameter Brass US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-026.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .246" Diameter Brass US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-027.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .120" Brass Alignment & Push Punch US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-025.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Set A US Specifications
USD 46.69
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-620-103.
More Details : click here
SEARCH this site : click here
|
|
|
Lyman Pistol Punch Set US Specifications
USD 17.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Five steel and brass gunsmith punches handle a variety of any pistol disassembly and reassembly jobs. Each precision-machined punch is through-hardened for maximum strength. Knurled handles ensure a firm grip to prevent slippage and protect your gun's finish from scratches and scuffs. Mfg: lyman specs: pin punches, 4140 chrome-moly steel. A, 3-3/8" (9.2cm) x 5/32" (4mm) diameter. B, 3-5/8" (9.2cm) long x 3/32" (2.4cm) dia. D, 4β½" (11.4cm) long x 5/32" (4mm) dia. F, 4βό" (10.8cm) long x 1/8" (3.2mm) dia. Drift punch brass. 3&f. US specification & reliable quality gunsmith punches by Lyman. Part Nr: 7031271.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .092" Diameter Brass US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-024.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches Set Of Four Brass Punches US Specifications
USD 35.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-028.
More Details : click here
SEARCH this site : click here
|
|
|
Starrett #565 Pin Punch Set Starrett Pin Punch 5/16" US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Precision ground from specially selected tool steel, hardened and highly polished, the starrett pin punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly. Mfg: starrett specs: 4" (10.2cm) long. Sizes: 1/16" (1.6mm), 3/32" (2.4cm), 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (5.5mm), βό" (6.3mm) and 5/16" (7.9mm). US specification & reliable quality gunsmith punches by Starrett. Part Nr: 52585.
More Details : click here
SEARCH this site : click here
|
|
|
Starrett #565 Pin Punch Set Starrett Pin Punch 1/8" US Specifications
USD 6.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Precision ground from specially selected tool steel, hardened and highly polished, the starrett pin punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly. Mfg: starrett specs: 4" (10.2cm) long. Sizes: 1/16" (1.6mm), 3/32 (2.4cm), 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (5.5mm), βό" (6.3mm) and 5/16" (7.9mm). US specification & reliable quality gunsmith punches by Starrett. Part Nr: 52580.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Mayhew Steel Single Starting Punches 1/16" Starting Punch US Specifications
|
 Copyright © RexGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
