Mayhew Steel Single Prick Punches 440 Prick Punch US Specifications
Gunsmith Punches by Mayhew
|
Technical data & information: Fine, sharp point for marking spots before center punching. Gives better visibility, more precision to your marking. Tap lightly as a mark only; use center punch to deepen for drilling. Mfg: mayhew steel specs: 5⁄16" (7.9mm) o.D., 4" (10.2cm) long. US specification & reliable quality gunsmith punches by Mayhew. Part Nr: 23200.
 Indicative Price: USD 6.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting items : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Ar 15 Lower Punch Set US Specifications
USD 65.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Safely remove pins without risk of damaging gun's finish handy 7-piece kit contains all the pin punches and roll pin holders necessary to assemble and disassemble an ar-15 lower receiver without damaging the gun's finish or the pins themselves. Our nylon punch won't leave a mark, while our special bolt catch pin punch is uniquely shaped to clear the side of the receiver while you drive the pin. Other punches for hammer/trigger pins, pivot/takedown pins, and triggerguard, plus additional punches for the forward assist pawl pin and gas tube roll pin on the upper receiver. Mfg: brownells specs: contains: bolt catch pin punch, 1/4" pin punch, 1/16" and 5/64"roll pin punches, 1/8" and 3/32" roll pin holders, and non-marring nylon punch. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-001-305.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Set A US Specifications
USD 46.69
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-620-103.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches Alignment/Push Punch Set US Specifications
USD 60.95
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-647.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Starter Punch .091 Dia. US Specifications
USD 9.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-513-091.
More Details : click here
SEARCH this site : click here
|
|
|
Starrett #565 Pin Punch Set Starrett Pin Punch 3/32" US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Precision ground from specially selected tool steel, hardened and highly polished, the starrett pin punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly. Mfg: starrett specs: 4" (10.2cm) long. Sizes: 1/16" (1.6mm), 3/32" (2.4cm), 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (5.5mm), βό" (6.3mm) and 5/16" (7.9mm). US specification & reliable quality gunsmith punches by Starrett. Part Nr: 52579.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pin Punch Set Of 3 W/2 1/2" Pins US Specifications
USD 24.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Finally! what we think is the answer to the pin punch headache that has plagued us, and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now, just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel, tensile strength of over 140,000 psi (min.). Replaceable punch, the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2β½" (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 β½" lengths. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-507-050.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pin Punch 2 1/2" Long .060 Dia. US Specifications
USD 10.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Finally! what we think is the answer to the pin punch headache that has plagued us, and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now, just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel, tensile strength of over 140,000 psi (min.). Replaceable punch, the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2β½" (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 β½" lengths. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-507-560.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #2 Punch US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25031939.
More Details : click here
SEARCH this site : click here
|
|
|
Grace Usa Brass Punch Set 3/32" (2.4mm) Brass Pin Punch US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For drifting sights, driving pins or fitting parts when marking or scratching the surface can mean the difference between a job well done and disaster. Machined from premium, brass hex. Punch set includes 8 flathead, long shaft punches for driving pins completely out. Mfg: grace usa specs: brass, 5⁄16" (7.9mm) hex stock. Punch set, 8 punches: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16", 7⁄32", ", 5⁄16" dia. US specification & reliable quality gunsmith punches by Grace. Part Nr: 332BPP.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Mayhew Steel Single Prick Punches 440 Prick Punch US Specifications
|
 Copyright © RexGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
