Mayhew Steel Single Starting Punches 5/32" Starting Punch US Specifications
Gunsmith Punches by Mayhew
|
 Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Alignment & Push Punches .092" Diameter Brass US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-024.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 5/64" Diameter Roll Pin Holder US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. US specification & reliable quality gunsmith punches by Brownells. Part Nr: B564RSH.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Brass Punch Set US Specifications
USD 119.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Precision machined, non-marring brass punches drift sights and drive pins without risk of damage to the sight, pin, or firearm. We combined 20 of our most popular non-marring brass punches, added a compact bench block and came up with a great addition for the work bench. Features (4) starter punches, (8) roll pin punches, and (8) standard punches for a variety of different jobs. Delrin bench block holds and organizes all 20 punches for easy access, plus is resistant to most solvents. Starter punches are used to start the removal of steel or aluminum pins. Short, tapered shaft is extra stiff to prevent bending and twisting. Roll pin punches feature a special tip that centers inside the h mfg: brownells specs: brass. Starter punches, contains (1) of each diameter: 1⁄16" (1.6mm), 3⁄32" (2.4mm), 1⁄8" (3.2mm), 5⁄32" (4mm). Roll pin punches, contains (1) of each diameter: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16". US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-649.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pins 2 1/2"x.039" US Specifications
USD 14.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Finally! what we think is the answer to the pin punch headache that has plagued us, and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now, just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel, tensile strength of over 140,000 psi (min.). Replaceable punch, the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2β½" (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 β½" lengths. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-510-639.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .246" Diameter Steel US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-032.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Set A US Specifications
USD 46.69
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-620-103.
More Details : click here
SEARCH this site : click here
|
|
|
Lyman Deluxe Hammer & Punch Set Hammer Punch Set US Specifications
USD 53.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Compact set of popular sized punches, with hammer, stores in its own bench block for quick access. Combination brass/nylon hammer has machine knurled handle for positive grip. 4130 steel punches. Mfg: lyman specs: set includes 1/16" (1.5mm), 3/32" (2.3mm), 1/8" (3.1mm), 5/32" (3.9mm), 3/16" (4.7mm) diameter pin punches, 1/8" center punch, 3/16" diameter brass drift. Brass/nylon face hammer, 8" (20cm) overall length, hardwood storage block. US specification & reliable quality gunsmith punches by Lyman. Part Nr: 7031298.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punch Set US Specifications
USD 109.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: We combined 19 of our most popular roll pin punches and added a handy bench block to come up with the perfect punch set for the busy shop or department armor. Easily start, remove, and install spring pins and roll pins in firearms without damage to the pin or firearm. Features (5) holder punches, (7) starter punches, and (7) standard punches that can easily handle any job out there. Made from solid steel, with parallel-ground shanks and knurled handles. Also includes a non-marring, nylon drift punch that won't damage or scrape delicate surface finishes. Machined, delrin bench block holds and organizes all the punches for easy access. Holder punches cup and hold roll pins, keeping mfg: brownells specs: punches, steel, knurled handle, matte black. Nylon punch, 4" (10cm) long x 5⁄16" (7.9mm) diameter. Holder punches, contains (1) of each diameter: 1⁄16" (1.6mm), 5⁄64" (2mm), 3⁄32" (2.4mm), 1⁄8" (3.2mm), 9⁄64" (3.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-651.
More Details : click here
SEARCH this site : click here
|
|
|
Starrett #565 Pin Punch Set Starrett Pin Punch 3/16" US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Precision ground from specially selected tool steel, hardened and highly polished, the starrett pin punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly. Mfg: starrett specs: 4" (10.2cm) long. Sizes: 1/16" (1.6mm), 3/32" (2.4cm), 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (5.5mm), βό" (6.3mm) and 5/16" (7.9mm). US specification & reliable quality gunsmith punches by Starrett. Part Nr: 52582.
More Details : click here
SEARCH this site : click here
|
|
|
Geissele Automatics Roll Pin Tool For Gas Block US Specifications
USD 12.5
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Ingenious tool holds the tiny gas tube roll pin securely to make installation easy and fast. No more fumbling with needle nose pliers or tweezers, only to have the pin fly fly off and get lost! pin is pressed into the tool for a rock-solid hold while the tapered tip enables precise control and correct placement. Safely gets the pin partially in, so the job can be finished with a normal roll pin punch. All-steel construction, matte black oxide finish. Mfg: geissele automatics llc. US specification & reliable quality gunsmith punches by Geissele. Part Nr: 10225.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #6 Punch US Specifications
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25035939.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Mayhew Steel Single Starting Punches 5/32" Starting Punch US Specifications
|
 Copyright © RexGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
