Brownells Roll Pin Holders #1 1/16"(1.6mm) Dia 4 1/2"(11.4cm) O/A Length US Specifications
Gunsmith Punches by Brownells
|
Technical data & information: Holds roll pins perfectly aligned for starting correctly. Especially good on the tiny, tough-to-grab ones, or those in tight places. 1/16" is notched to clear m16/ar-15 rear sight. 3.5mm excellent for holding the pin that retains the breech block on sig handguns. Finish driving with roll pin punch. O/a in chart means "overall". Available individually or as a set of 5. Mfg: brownells specs: steel, knurled handle. Set of 5. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-685-062.
 Indicative Price: USD 14.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting items : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Starter Punch Set Replaceable Pins (6) 1"x.039" US Specifications
USD 9.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-513-639.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 1/16" Diameter Roll Pin Holder US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. US specification & reliable quality gunsmith punches by Brownells. Part Nr: B232RSH.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Starter Punch Set US Specifications
USD 22.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-513-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 3/32" Diameter Roll Pin Holder US Specifications
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. US specification & reliable quality gunsmith punches by Brownells. Part Nr: B332RSH.
More Details : click here
SEARCH this site : click here
|
|
|
Gauge Rite Products Top Dead Center Punch US Specifications
USD 37.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: The tdc is a rugged, foolproof tool to end the problems of off-center-work, broken taps and drills that come about from trying to "eyeball" top dead center on gun barrels or other round stock. Simple to use, just level and plumb the rifle on the drill press, place tdc on barrel or receiver, level the bubble and tap the punch. The punch mark is top dead center. Precision made; shockproof level. Mfg: gauge-rite products specs: body, 1-15/16" (23.8mm) x 1-β½" (3.8mm) x 1" (2.5cm), aluminum. Punch, βό" (6.3mm) diameter tool steel. Locating rod, 5-β½" (14cm) long. US specification & reliable quality gunsmith punches by Gauge-Rite. Part Nr: 871-100-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Hole Center Punches #10 Hole Center Punch US Specifications
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-732-010.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches Set Of Four Brass Punches US Specifications
USD 35.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-028.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pins 2 1/2"x.091" US Specifications
USD 15.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: Finally! what we think is the answer to the pin punch headache that has plagued us, and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now, just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel, tensile strength of over 140,000 psi (min.). Replaceable punch, the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2β½" (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 β½" lengths. US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-510-691.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #7 Roll Pin Punch US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 25006939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .092" Diameter Steel US Specifications
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches US Specifications
Technical data & information: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). US specification & reliable quality gunsmith punches by Brownells. Part Nr: 080-000-029.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Roll Pin Holders #1 1/16"(1.6mm) Dia 4 1/2"(11.4cm) O/A Length US Specifications
|
 Copyright © RexGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
